Описание: (1) Fix the bug: 686B IDE not detected. (2) 686B_support (3) Ultra DMA support (4) logo_setup_abnormal (5) AMR wakeup support (6) No suggested SDRAM Clock (7) AC97 Audio Codec Subsystem ID & Subsystem Vendor ID (8) Add Shuttle' brand in DMI (9) Add [MV16/MV17] sign on message (10) record power on status (11) set DRAM driving strength = 6FH (12) show IDE model in setup & HDD show size (13) quick post as default (14) remove "Bank 4/5 DRAM Timing" item (15) Default value of "Sound Blaster" = Enabled (16) Default value of "State after power fail" = Auto (17) DRAM Driving strength = 7FH (18) Default value of "Bank 0/1 DRAM driving" = normal (19) Default value of "Bank 2/3 DRAM driving" = normal (20) change string length of IDE configuration from 14 to 10 (21) Default value of "Bank 0/1 DRAM driving" = 8/10 (22) Default value of "Bank 2/3 DRAM driving" = 8/10 (23) Default value of "Sound Blaster" = Disabled (24) solve: ATA 66 shows as ATA 33 with 686A (25) Solve: if only HDD and no CDROM is connected, then system can not boot up into Win98 & WinME. (26) Not to set DRAM driving strength (27) remove "DRAM Bank 0/1 Driving Strength" item (28) remove "DRAM Bank 2/3 Driving Strength" item (29) add a "DRAM Drive Strength" item (30) clear memory and set VGA mode in order that the abnormal picture found in pressing [DEL] buttton to enter setup menu won't happen again (31) set the DRAM drive strength according to new algorithm, such algorithm is perhaps suggested by VIA (32) add IDE subsystem ID and subsystem vendor ID, such modification can solve the problem that if some kind of CD-ROM is plugged, then the system can not resume from S3. (33) Save HDD PIO mode before entering S3 mode, such modification can solve the problem that if some kind of CD-ROM is plugged and DMA is enabled, then the system can not resume from S3. (34) Set DRAM driving strength according to the following algorithm (34.1) one bank: 21h (34.2) two banks: 21h (34.3) three banks: 2Dh (34.4) four banks: 6Fh (35) show CDRW (36) remove "USB mouse support" item (37) abnormal screen setup (38) set the default value of "State after Power Failure" to "off" (39) Solve the problem that if USB Mouse is plugged, then S3/resume will fail with WinME (40) fix bug: WOL resume from s5 fails under Win98 SE (41) fix bug: WOL resume from s1 & S3 fails under Win98 SE
Ultra ATA Driver » Intel Ultra ATA Driver - The Intel® Ultra ATA Storage Driver enables fast Ultra ATA transfers for a variety of IDE/ATAPI devices such as hard drives and CD-ROMs. Ver.6.10 (Multi language)for WinNT 4.0/2000/98/98SE/Me
CS62-TC » Bios - 1.Support ATA 133 HDD string in PCI table. 2.Slove ATA 100 HDD active Ultra DMA Mode 5 on Win XP when connect to Primary Master IDE. 3.Support Celeron-T 1.3G. 4.Support bioslock feature.
Технология AMR (Audio/Modem Riser Card) - Одна из наиболее заметных в последнее время инициатив Intel - это не продвижение какой-либо новой технологии, а напротив, попытка уничтожить уже существующую. Речь идет
EAZ-FIX, Recover Dead PC in a Moment - What does it take to kill a computer? A virus, immature software failed performance test, hitting a wrong button or kids new «discovery» at home the disasters are numerous, and the consequence is the same at all times; you have to recover your lost data and oftentimes that assumes the